Curved elements are available only in RFEM. It's possible to intersect curved surfaces and solids.
When doing this, the program generates surfaces with the "Trimmed" surface type. With this technology, you can create very complex geometries, such as pipe intersections or curved openings, with a single click.
The intersection of solids is carried out adaptively using the new solid types "Hole" and "Intersection", according to the set theory. Use this method to create new, complex solid geometries similar to the manufacturing process (drilling, milling, turning, etc.). Therefore, it is possible to create complex curved surface or perforated solid elements. It's a simple process!
After activating the RF‑PIPING add‑on module, a new toolbar is available in RFEM and the project navigator and tables are extended. The piping system is now modeled in the same way as the members. Pipe bends are defined simultaneously by tangents (straight pipe sections) and radius. Thus, it is easy to subsequently change bend parameters.
It is also possible to extend the piping subsequently by defining special components (expansion joints, valves, and others). The implemented libraries of structural components facilitate the definition.
Continuous pipe sections are defined as sets of piping systems. For piping loads, member loads are assigned to the respective load cases. The combination of loads is included in piping load combinations and result combinations. After the calculation, you can display deformations, member internal forces, and support forces graphically or in tables.
Pipe stress analysis according to standards can then be performed in the RF‑PIPING Design add‑on module. You only need to select the relevant sets of piping systems and load situations.
The member hinge nonlinearities "Scaffolding - N phiy / phiz" and "Scaffolding Diagram" enable the mechanical simulation of a tube joint with an inner stub between two member elements.
The equivalent model transfers the bending moment via the overpressed outer pipe and after positive locking additionally via the inner stub, depending on the compression state at the member end.
Design of tension, compression, bending, shear, and combined internal forces
Stability analysis for flexural buckling and lateral-torsional buckling
Automatic determination of critical buckling loads and critical buckling moments for general load applications and support conditions by means of a special FEA program (eigenvalue analysis) integrated in the module
Optional application of discrete lateral supports to beams
Automatic cross-section classification
Deformation analysis (serviceability)
Cross-section optimization
Wide range of cross-sections available, such as rolled I-sections, C-sections, rectangular hollow sections, angles, double angles (arrangement flange on flange), T-sections. Welded sections: I-shaped (symmetrical and asymmetrical about major axis), channel sections (symmetrical about major axis), rectangular hollow sections (symmetrical and asymmetrical about major axis), angles, round pipes, and round bars
Clearly arranged result tables
Detailed result documentation including references to design equations of the used standard
Various filter and sorting options of results, including result lists by member, cross-sections, x-location, or by load case, load and result combination
Result table of member slenderness and governing internal forces
Design of tension, compression, bending, shear, and combined internal forces
Stability analysis for flexural buckling and lateral-torsional buckling
Automatic determination of critical buckling loads and critical buckling moments for general load applications and support conditions by means of a special FEA program (eigenvalue analysis) integrated in the module
Optional application of discrete lateral supports to beams
Automatic cross-section classification
Deformation analysis (serviceability)
Cross-section optimization
Wide range of cross-sections available, such as rolled I-sections, C-sections, rectangular hollow sections, angles, double angles (arrangement flange on flange), T-sections. Welded sections: I-shaped (symmetrical and asymmetrical about major axis), channel sections (symmetrical about major axis), rectangular hollow sections (symmetrical and asymmetrical about major axis), angles, round pipes, and round bars
Clearly arranged result tables
Detailed result documentation including references to design equations of the used standard
Various filter and sorting options of results, including result lists by member, cross-sections, x-location, or by load case, load and result combination
Result table of member slenderness and governing internal forces
Design of tension, compression, bending, shear, and combined internal forces
Stability analysis for flexural buckling and lateral-torsional buckling
Automatic determination of critical buckling loads and critical buckling moments for general load applications and support conditions by means of a special FEA program (eigenvalue analysis) integrated in the module
Optional application of discrete lateral supports to beams
Automatic cross-section classification (Class 1 to 3)
Deformation analysis (serviceability)
Cross-section optimization
Wide range of cross-sections available, such as rolled I-sections, C-sections, rectangular hollow sections, angles, double angles (arrangement flange on flange), T-sections. Welded sections: I-shaped (symmetrical and asymmetrical about major axis), channel sections (symmetrical about major axis), rectangular hollow sections (symmetrical and asymmetrical about major axis), angles, round pipes, and round bars
Clearly arranged result tables
Detailed result documentation including references to design equations of the used standard
Various filter and sorting options of results, including result lists by member, cross-sections, x-location, or by load case, load and result combination
Result table of member slenderness and governing internal forces
After modeling piping systems in RFEM using RF‑PIPING and defining loads as well as load and result combinations, you can carry out pipe stress analysis in the RF‑PIPING Design add‑on module.
You can select all or only some pipelines and loads, load or result combinations for piping design. The material library provides various materials according to EN 13480‑3, ASME B31.1‑2012, and ASME B31.3‑2012 standards.
After the calculation, the results are displayed in clearly arranged windows; for example, by cross‑section, by pipeline, or by members. You can also display the design ratio graphically on the entire model in RFEM. This way, you can quickly recognize critical or oversized areas of the cross-section.
In addition to the input and result data, including design details displayed in tables, you can add all graphics into the printout report. This way, comprehensible and clearly arranged documentation is guaranteed. You can select the report contents and extent specifically for the individual designs.
In a separate dialog box, you can specify extensive detailed settings for the design:
Design Method According to DIN 18800
Design Method 1 According to El. (321)
Design Method 2 According to El. (322)
Analysis method
Elastic-Plastic according to DIN 18800
Elastic-elastic according to a publication by Kretschmar, J./Österrieder, P./beirow, B.
Limit loading of general sections
General sections – these include all cross-sections that cannot be assigned to single or double symmetric I-sections, box sections, or pipe sections – can also be designed according to the equivalent member method against flexural buckling. In this case, however, the plastic cross-section properties are determined without interaction conditions. The allowable application limits for this consideration depend on the ratio of the existing internal force to the fully plastic internal force. Five text boxes provide the option for user-defined control.
Check of limit (c/t)
In this dialog section, you can activate or deactivate the check of c/t ratios.
Treatment of Result Combinations
When designing a result combination, a result set is obtained due to the result superposition on each member location, which makes it impossible to clearly determine the moment factors. In this section, you can thus freely specify a global moment factor for a result combination design. The predefined values are on the safe side, regardless of the design method.
Design of tension, compression, bending, shear, and combined internal forces
Stability analysis for flexural buckling and lateral-torsional buckling
Automatic determination of stability factors according to Annexes E, F, and G
Optional application of discrete lateral supports to beams
Automatic slenderness check of cross-section parts under compression
Deformation analysis (serviceability)
Cross-section optimization
Wide range of cross-sections available, such as rolled I-sections, channel sections, rectangular hollow sections, angles, T-sections. Welded sections: I-shaped (symmetrical and asymmetrical about major axis), channel sections (symmetrical about major axis), rectangular hollow sections (symmetrical and asymmetrical about major axis), angles, round pipes, and round bars
Clearly arranged result tables
Detailed result documentation including references to design equations of the used standard
Various filter and sorting options of results, including result lists by member, cross-sections, x-location, or by load case, load and result combination
Result table of member slenderness and governing internal forces
Design of tension, compression, bending, shear, and combined internal forces
Stability analysis for flexural buckling and lateral-torsional buckling
Automatic determination of critical buckling loads and overall stability factors for lateral-torsional buckling according to Annex B
Optional application of discrete lateral supports to beams
Automatic local stability analysis and check of plastic design criteria of a cross-section
Deformation analysis (serviceability)
Cross-section optimization
Wide range of cross-sections available, such as rolled I-sections, channel sections, rectangular hollow sections, angles, T-sections. Welded sections: I-shaped (symmetrical and asymmetrical about major axis), channel sections (symmetrical about major axis), rectangular hollow sections (symmetrical and asymmetrical about major axis), angles, round pipes, and round bars
Clearly arranged result tables
Detailed result documentation including references to design equations of the used standard
Various filter and sorting options of results, including result lists by member, cross-sections, x-location, or by load case, load and result combination
Result table of member slenderness and governing internal forces
Full integration in RFEM/RSTAB including import of all relevant internal forces
Intelligent presetting of flexural buckling-specific design parameters
Automatic determination of the distribution of internal forces and classification according to DIN 18800, Part 2
Optional import of buckling lengths from the RF-STABILITY/RSBUCK add-on module. For this, a comfortable graphical selection of the relevant buckling mode is possible
Optimizing Cross-Sections
Optional calculation according to both design methods of DIN 18800, Part 2
Automatic determination of the most unfavorable design location, also for tapered members
Check of c/t-limit values according to DIN 18800, Part 1
Design of any thin-walled RFEM/RSTAB or SHAPE-THIN section for compression and bending without interaction according to the elastic-plastic method
Design of I-shaped rolled and welded sections, I-like sections, box sections, and pipes subjected to bending and compression with iteration according to the elastic-plastic method
Clearly arranged, comprehensible design checks with all intermediate values in the short and long forms
Design of tension, compression, bending, shear, combined internal forces, and torsion
Stability analysis for flexural buckling, torsional buckling, and lateral-torsional buckling
Optional application of discrete lateral supports to beams
Deformation analysis (serviceability)
Cross-section optimization
Wide range of cross-sections available, such as rolled I-sections, channel sections, rectangular hollow sections, angles, T-sections. Welded sections: I-shaped (symmetrical and asymmetrical about major axis), channel sections (symmetrical about major axis), rectangular hollow sections (symmetrical and asymmetrical about major axis), angles, round pipes, and round bars
Clearly arranged result tables
Detailed result documentation including references to design equations of the used standard
Various filter and sorting options of results, including result lists by member, cross-sections, x-location, or by load case, load and result combination
Result table of member slenderness and governing internal forces